2-Set Frame of Cast Iron Ensure Verticality
The guiding holes are cast at bed and machined at the same time.
Separated Clutch and Brake
The torch of separated clutch & brake is bigger, so braking time and angle get less. Balanced load at two side can reduces wear of bearings. If mechanical parts fail at clutch or brake, press stops immediately.
Normal Clutch
Separated Clutch & Brake
Design of Knuckle Structure
Movement of Slide
Guiding System of Slide & Hydro-Static Bushings
Dual plungers bear up more upward eccentric load during stamping. Hydro-static bushings can stand with higher thrust, decrease friction area, and suppress heat expansion to prevent the wear of bearing throughout years.
Siemens Colorful Automatic Computer Control System
Colorful HMI screen is applied to display press situation friendly by colors,schematic and letters.
Knuckle vs Crank Slide Movement
- Eccentric load's deformation is 1/3 of crank type.
- Total clearance is under 50% of JIS special grade.
- Above 1mm to BDC period is double of crank type.
Machine Specification
| Type | Apex-30 | Apex-45 | Apex-60 | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Capacity | tons | 30 | 45 | 60 | |||||||||
| Slide stroke | mm | 10 | 20 | 30 | 40 | 10 | 20 | 30 | 40 | 20 | 30 | 40 | 50 |
| Press Speed | spm | 200 | 1400 |
200 | 1200 |
200 | 1000 |
200 | 800 |
200 | 1300 |
200 | 1100 |
200 | 900 |
200 | 700 |
200 | 1000 |
200 | 800 |
200 | 600 |
200 | 500 |
| Shut Height | spm | 255 | 250 | 245 | 240 | 285 | 280 | 275 | 270 | 325 | 320 | 315 | 310 |
| Area of Bolster | mm | 600 x 450 | 800 x 550 | 1000 x 650 | |||||||||
| Bolster thickness | mm | 100 | 120 | 140 | |||||||||
| Area of Slide | mm | 600 x 340 | 800 x 400 | 1000 x 450 | |||||||||
| Shut Height adjustment | mm | 40 | 50 | 50 | |||||||||
| Main Motor | hp | 15 | 15 | 20 | |||||||||
Dimension of Press
| Type | Apex-30 | Apex-45 | Apex-60 | |
|---|---|---|---|---|
| Height of Press (A) | mm | 2270 | 2510 | 2810 |
| Height for Operation (B) | mm | 800 | 850 | 950 |
| Height for Scrap out (C) | mm | 330 | 310 | 290 |
| Width of Press (D) | mm | 1150 | 1350 | 1650 |
| Depth of Press (F) | mm | 1100 | 1200 | 1400 |
| Height of feed line (G) | mm | 100 ± 20 | 115 ± 20 | 135 ± 20 |
| Width of Upright opening (H) | mm | 220 | 260 | 300 |
| Net Weight | tons | 5 | 8 | 12 |
* We reserve the right to modify all data contained in this catalogue without notice. Please contact with us for detail specification & dimension of the press.
Machine Specification
| Type | Apex-K VIII | Apex-K XII | Apex-K XVI | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Capacity | tons | 80 | 125 | 160 | |||||||||
| Slide stroke | mm | 20 | 30 | 40 | 50 | 20 | 30 | 40 | 50 | 20 | 30 | 40 | 50 |
| Press Speed | spm | 200 | 700 |
200 | 600 |
200 | 500 |
200 | 400 |
200 | 600 |
200 | 500 |
200 | 400 |
200 | 300 |
200 | 500 |
200 | 400 |
200 | 300 |
200 | 200 |
| Shut Height | spm | 365 | 360 | 355 | 350 | 385 | 380 | 375 | 370 | 385 | 380 | 375 | 370 |
| Area of Bolster | mm | 1200 x 750 | 1400 x 850 | 1700 x 850 | |||||||||
| Bolster thickness | mm | 140 | 160 | 160 | |||||||||
| Area of Slide | mm | 1200 x 500 | 1400 x 640 | 1700 x 640 | |||||||||
| Shut Height adjustment | mm | 50 | 50 | 50 | |||||||||
| Main Motor | hp | 30 | 30 | 40 | |||||||||
Dimension of Press
| Type | Apex-K VIII | Apex-K XII | Apex-K XVI | |
|---|---|---|---|---|
| Height of Press (A) | mm | 3600 | 3800 | 4300 |
| Height for Operation (B) | mm | 1010 | 1060 | 1080 |
| Height for Scrap out (C) | mm | 300 | 280 | 130 |
| Width of Press (D) | mm | 1930 | 2200 | 2600 |
| Depth of Press (F) | mm | 1600 | 1800 | 2000 |
| Height of feed line (G) | mm | 155 ± 20 | 165 ± 20 | 165 ± 20 |
| Width of Upright opening (H) | mm | 350 | 400 | 450 |
| Net Weight | tons | 18 | 25 | 32 |
* We reserve the right to modify all data contained in this catalogue without notice. Please contact with us for detail specification & dimension of the press.
Standard Accessories
- Slide adjust motor (0.01 mm)
- Front-rear safety door
- Joint for air gun x 1
- Mis-feed joint x 4
- Batch, Cam joint x 5
- Inverter
- Centralized workstation system
- Siemens coutrol system with load monitior
- Anti-vibration spring type cushion (Apex-Knuckle)
- Die arm (Apex60 above)
- Die lifter (Apex-Knuckle)
Optional Accessories
- Slide quick lift
- Gripper Feed
- Gear Change Roll Feed
- Straightener + S-Loop (Lamination)
- Dual Head Coiler (Lamination)
ING YU was established in 1970 and specialized in the manufacture of Precision Stamping, Precision Metal Stamping, Progressive Die Stamping, Metal Stamping Press and Complex Metal Forming. We believe that design is the key to quality and insist to offer the best quality press to worldwide customers.
Contact Us
No.43-11, Sha-Tien Rd., Sha-Lu Dist., Taichung City, Taiwan
Phone: 886-4-26358569
Fax: 886-4-26353068